FOREWORD

This Supplementary Service Manual has been prepared to introduce new service and data for the

XVS1100A. For complete service information procedures it is necessary to use this Supplementary

Service Manual together with the following manual.

XVS1100L/XVS1100LC SERVICE MANUAL: LIT-11616-12-63 (5EL-28197-E0)

XVS1100AM/XVS1100AMC SUPPLEMENTARY SERVICE MANUAL:

LIT-11616-13-36 (5KS-28197-E0)

EB000000

XVS1100AWR(C)

XVS1100ATR(C)

SUPPLEMENTARY

SERVICE MANUAL

 2002 by Yamaha Motor Co., Ltd.

First edition, November 2002

All rights reserved. Any reproduction or

unauthorized use without the written

permission of Yamaha Motor Co., Ltd.

is expressly prohibited.

NOTE:

WARNING

CAUTION:

EAS00003

NOTICE

This manual was produced by the Yamaha Motor Company, Ltd. primarily for use by Yamaha dealers

and their qualified mechanics. It is not possible to include all the knowledge of a mechanic in one manu-

al. Therefore, anyone who uses this book to perform maintenance and repairs on Yamaha Vehicles

should have a basic understanding of mechanics and the techniques to repair these types of vehicles.

Repair and maintenance work attempted by anyone without this knowledge is likely to render the ve-

hicle unsafe and unfit for use.

This model has been designed and manufactured to perform within certain specifications in regard to

performance and emissions. Proper service with the correct tools is necessary to ensure that the ve-

hicle will operate as designed. If there is any question about a service procedure, it is imperative that

you contact a Yamaha dealer for any service information changes that apply to this model. This policy

is intended to provide the customer with the most satisfaction from his vehicle and to conform with

federal environmental quality objectives.

Yamaha Motor Company, Ltd. is continually striving to improve all of its models. Modifications and sig-

nificant changes in specifications or procedures will be forwarded to all authorized Yamaha dealers

and will appear in future editions of this manual where applicable.

This Service Manual contains information regarding periodic maintenance to the emission control sys-

tem. Please read this material carefully.

Designs and specifications are subject to change without notice.

IMPORTANT INFORMATION

Particularly important information is distinguished in this manual by the following notations.

The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR

SAFETY IS INVOLVED!

Failure to follow WARNING instructions could result in severe injury or death to

the motorcycle operator, a bystander or a person inspecting or repairing the

motorcycle.

A CAUTION indicates special precautions that must be taken to avoid damage

to the motorcycle.

NOTE:

A NOTE provides key information to make procedures easier or clearer.

1

2

6

3

5

4

7

8

EB002000

HOW TO USE THIS MANUAL

MANUAL ORGANIZATION

This manual consists of chapters for the main categories of subjects. (See “Illustrated symbols”)

1st title 1 :

This is the title of the chapter with its symbol in the upper right corner of each page.

2nd title 2 :

This title indicates the section of the chapter and only appears on the first page of each

section. It is located in the upper right corner of the page.

3rd title 3 :

This title indicates a sub-section that is followed by step-by-step procedures accompa-

nied by corresponding illustrations.

EXPLODED DIAGRAMS

To help identify parts and clarify procedure steps, there are exploded diagrams at the start of each re-

moval and disassembly section.

1. An easy-to-see exploded diagram 4 is provided for removal and disassembly jobs.

2. Numbers 5 are given in the order of the jobs in the exploded diagram. A number that is enclosed by

a circle indicates a disassembly step.

3. An explanation of jobs and notes is presented in an easy-to-read way by the use of symbol marks

6 . The meanings of the symbol marks are given on the next page.

4. A job instruction chart 7 accompanies the exploded diagram, providing the order of jobs, names of

parts, notes in jobs, etc.

5. For jobs requiring more information, the step-by-step format supplements 8 are given in addition to

the exploded diagram and the job instruction chart.

22

1

3

5

7

9

2

4

8

6

24

23

21

19

18

16

15

14

13

11

12

10

GEN

INFO

SPEC

ENG

CARB

ELEC

CHAS

CHK

ADJ

TRBL

SHTG

20

17

EB003000

ILLUSTRATED SYMBOLS

The following symbols are not relevant to every

vehicle.

Symbols 1 to 8 indicate the subject of each

chapter.

1 General information

2 Specifications

3 Periodic checks and adjustments

4 Engine

5 Carburetor

6 Chassis

7 Electrical system

8 Troubleshooting

Symbols 9 to ¹⁶ indicate the following.

9 Serviceable with engine mounted

10 Filling fluid

11 Lubricant

12 Special tool

13 Tightening torque

14 Wear limit, clearance

15 Engine speed

16 Electrical data

Symbols ¹⁷ to ²² in the exploded diagrams indi-

cate the types of lubricants and lubrication

points.

17 Engine oil

18 Gear oil

19 Molybdenum disulfide oil

20 Wheel bearing grease

21 Lithium soap base grease

22 Molybdenum disulfide grease

Symbols ²³ to ²⁴ in the exploded diagrams indi-

cate the following:

23 Apply locking agent (LOCTITE
)

24 Replace the part

CONTENTS

SPECIFICATIONS

GENERAL SPECIFICATIONS

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MAINTENANCE SPECIFICATIONS

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ENGINE

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CHASSIS

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ELECTRICAL

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CABLE ROUTING

5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PERIODIC CHECKS AND ADJUSTMENTS

INTRODUCTION

15

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PERIODIC MAINTENANCE CHART FOR THE EMISSION CONTROL

SYSTEM

15

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

GENERAL MAINTENANCE AND LUBRICATION CHART

15

. . . . . . . . .

CHASSIS

FRONT WHEEL AND BRAKE DISCS

17

. . . . . . . . . . . . . . . . . . . . . . . . . . .

REMOVING THE FRONT WHEEL

19

. . . . . . . . . . . . . . . . . . . . . . . . . . .

CHECKING THE FRONT WHEEL

19

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

CHECKING THE BRAKE DISCS

21

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

INSTALLING THE FRONT WHEEL

23

. . . . . . . . . . . . . . . . . . . . . . . . . . .

REAR WHEEL AND BRAKE DISC

24

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MUFFLER AND BRAKE CALIPER

24

. . . . . . . . . . . . . . . . . . . . . . . . . . .

REAR WHEEL

25

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

REMOVING THE REAR WHEEL

27

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CHECKING THE REAR WHEEL

27

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CHECKING THE REAR WHEEL DRIVE HUB

28

. . . . . . . . . . . . . . . . .

INSTALLING THE REAR WHEEL

28

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

ELECTRICAL

CHECKING THE SWITCHES

30

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

XVS1100AWR(C)/XVS1100ATR(C) WIRING DIAGRAM

–1–

GENERAL SPECIFICATIONS

SPEC

SPECIFICATIONS

GENERAL SPECIFICATIONS

Item

Standard

Model code

XVS1100: 5KSJ (For U.S.A.)

5KSK (For CAL)

5KSU (For U.S.A.)

5KSV (For CAL)

Dimensions

Overall length

Overall width

Overall height

2460 mm (96.9 in)

945 mm (37.2 in)

1,095 mm (43.1 in)

Seat height

Wheelbase

Minimum ground clearance

Minimum turning radius

710 mm (28 in)

1645 mm (64.8 in)

140 mm (5.5 in)

3400 mm (133.9 in)

Basic weight

With oil and a full fuel tank

285 kg (628 lb)

Tire

Type

Size

front

rear

Manufacturer

front

rear

Type

front

rear

Tubeless

130/90-16M/C 67S

170/80-15M/C 77S

BRIDGESTONE/DUNLOP

BRIDGESTONE/DUNLOP

EXEDRA G703/D404F

EXEDRA G702/D404G

Tire pressure (cold tire)

0
90 kg (0
198 lb) load*

front

rear

90 kg (198 lb)
Maximum load*

front

rear

225 kPa (2.25 kg/cm², 32.6 psi)

250 kPa (2.5 kg/cm², 36.3 psi)

225 kPa (2.25 kg/cm², 32.6 psi)

250 kPa (2.5 kg/cm², 36.3 psi)

* Load is the total weight of the cargo, rider,

passenger and accessories.

–2–

MAINTENANCE SPECIFICATIONS

SPEC

MAINTENANCE SPECIFICATIONS

ENGINE

Item

Standard

Limit

Carburetor

I.D. mark

Main jet

(M.J)

Main air jet

(M.A.J)

Jet needle

(J.N)

Needle jet

(N.J)

Pilot air jet

(P.A.J.1)

(P.A.J.2)

Pilot outlet

(P.O)

Pilot jet

(P.J)

Bypass 1

(B.P.1)

Bypass 2

(B.P.2)

Bypass 3

(B.P.3)

Valve seat size

(V.S)

Starter jet

(G.S.1)

Starter jet

(G.S.2)

Throttle valve size

(Th.V)

Fuel level (above the line on

the float chamber)

(F.L)

Engine idle speed

Intake vacuum

Engine oil temperature

5EL5 40 (U.S.A.)

5EL6 50 (CAL)

#1: #110, #2: #112.5

#55

5DL 43-53-1

P-0M

#63.8

#145

1.0

#17.5

0.8

0.8

0.8

1.2

#42.5

0.8

#125

4
5 mm (0.16
0.20 in)

950
1,050 r/min

34.7
37.3 kPa (260
280 mmHg)

75
85
C (167
185
F)











































Fuel pump

Type

Model/manufacturer

Consumption amperage

<max>

Output pressure

Electrical type

UC-Z61B/MITSUBISHI

0.8 A

12 kPa (0.12 kg/cm²,1.7 psi)









CHASSIS

Item

Standard

Limit

Front suspension

Front fork travel

Fork spring free length

Fitting length

Collar length

Spring rate

(K1)

(K2)

Stroke

(K1)

(K2)

Optional spring

Oil capacity

Oil level

Oil grade

140 mm (5.51 in)

371.9 mm (14.64 in)

334.4 mm (13.17 in)

183 mm (7.20 in)

4.41 N/mm (0.45 kg/mm, 25.18 lb/in)

6.37 N/mm (0.65 kg/mm, 36.37 lb/in)

0
77.5 mm (0
3.05 in)

77.5
140 mm (3.05
5.51 in)

No

0.483 L (483 cm³, 17.01 Imp OZ,

16.34 US OZ)

104 mm (4.09 in)

Fork oil 10WT or equivalent



350 mm

(13.78 in)





















–3–

MAINTENANCE SPECIFICATIONS

SPEC

Item

Standard

Limit

Rear suspension

Shock absorber travel

Spring free length

Fitting length

Spring rate

(K1)

Stroke

(K1)

Optional spring

51 mm (2.01 in)

181 mm (7.13 in)

169 mm (6.65 in)

132.3 N/mm (13.49 kg/mm, 755.43 lb/in)

0
51 mm (0
2.01 in)

No













Front wheel

Type

Rim size

Rim material

Rim runout limit

radial

lateral

Cast wheel

16M/C  MT 3.00

Aluminum











1.0 mm

(0.04 in)

0.5 mm

(0.02 in)

Rear wheel

Type

Rim size

Rim material

Rim runout limit

radial

lateral

Cast wheel

15M/C  MT4.50

Aluminum











1.0 mm

(0.04 in)

0.5 mm

(0.02 in)

ELECTRICAL

Item

Standard

Limit

T.C.I.

Pickup coil resistance/color

T.C.I. unit model/manufacturer

189
231 Ω at 20
C (68
F)/Gray – Black

J4T142/MITSUBISHI





Rectifier/regulator

Regulator type

Model/manufacturer

Semi-conductor, short-circuit type

SH678-11/SHINDENGEN





No load regulated voltage

Rectifier capacity

Withstand voltage

14.1
14.9 V

22 A

200 V







–4–

MAINTENANCE SPECIFICATIONS

SPEC

Item

Standard

Limit

Electric starter system

Type

Starter motor:

Model/manufacturer

Output

Armature coil resistance

Brush overall length

Brush spring pressure

Commutator diameter

Mica undercut

Starter relay:

Model/manufacturer

Amperage rating

Constant mesh type

SM-13/MITSUBA

0.6 kW

0.025
0.035 Ω at 20
C (68
F)

12.5 mm (0.49 in)

7.65
10.01 N

(780
1021 g, 27.51
36.01 OZ)

28 mm (1.10 in)

0.7 mm (0.03 in)

MS5F-421/JIDECO

180 A









4 mm

(0.16 in)



27 mm

(1.06 in)







Starting circuit cut-off relay

Model/manufacturer

Coil resistance

G8R-30Y-U/OMRON

202.5
247.5 Ω at 20
C (68
F)



Thermostat switch

Model/manufacturer

5FU/NIPPON THERMOSTAT



–5–

CABLE ROUTING

SPEC

1 Clutch cable

2 Starter cable

3 Handlebar switch lead (left)

4 Handlebar switch lead (right)

5 Spark plug lead

6 Throttle cable

7 Fuel hose (fuel cock to filter)

8 Fuel breather hose (fuel tank roll

over valve) (for CAL)

9 Fuse box

10 Alarm connector

11 Fuel pump lead

12 Speed sensor lead

13 Sidestand switch lead

14 Neutral switch lead

15 Pickup coil lead

16 To engine

17 A.C. magneto lead

18 Ventilation hose

19 Sensing hose (AI system to car-

buretor joint)

20 Fuel hose (fuel pump to carbure-

tor)

21 Clip

22 Brake hose

23 Heat protector

24 Speedometer lead

25 Wire harness

26 Purge hose (carburetor to sole-

noid valve) (for CAL)

27 Fitting plate

28 Fuel hose (inlet) (fuel filter to fuel

pump)

29 Fuel hose (outlet) (fuel pump to

carburetor)

30 Alarm connector lead

31 Wire harness

EB206000

CABLE ROUTING

–6–

CABLE ROUTING

SPEC

A Fasten the handlebar switch

lead (left and right) to the handle-

bar with plastic locking tie and

cut the end of tie.

B Lay out the throttle and starter

cables in three rows and secure

them with a clip. (Two points at

the front and rear.) Care should

be taken at this time so that the

clip does not fall to the outside

against the vertical face of the

vehicle. Point the opening part of

the clip to the inside of the ve-

hicle.

C Clamp the wire harness with the

hook of frame side.

D When installing the pipe of

throttle cable press it inside.

E Clamp the fuel hoses to the

frame with the clamp.

F Cross the fuel hose (fuel cock

side) and fuel hose (carburetor

side) between guide of frame

and clamp. (carburetor side is

upper)

G When connecting the sensing

hose (carburetor joint to AI sys-

tem) with a nozzle.

H Push the wire harness inside of

the side cover.

I Push the sensing hose inside of

the tool box plate and not bend

the sensing hose.

J Through the wire harness of so-

lenoid valve between AIS duct

and fuel hose (for CAL).

K Fasten the alarm lead with a plas-

tic band on the tool box plate.

L Fasten the sidestand switch lead

to the bracket of tool box plate

with plastic locking tie.

–7–

CABLE ROUTING

SPEC

M Fasten the lead with locking tie

near the side cover.

N Position the all connectors inside

of the connector cover.

O Route the clutch cable through

the cable guide.

P Fasten the handlebar switch

leads (left and right) under the

handle crown with a plastic

band. Set the band at four

notches and install it no slacking.

Q Route the each hoses through the

frame guide and do not pinch it.

R When installing the fitting plate,

do not pinch the each hoses and

wireharness.

S When install the AI system push

the wire harness to space of rear-

side.

–8–

CABLE ROUTING

SPEC

1 Battery

2 Battery positive (+) lead

3 Starter motor positive (+) lead

4 Speedometer lead

5 Fuel hose (fuel pump to carbure-

tor)

6 Spark plug lead

7 Main switch lead

8 Throttle cable

9 Front brake hose

10 Handlebar switch lead (right)

11 Headlight lead

12 Ignition coil

13 Breather hose

14 Purge hose (carburetor to sole-

noid valve) (For CAL)

15 Rear brake switch

16 Reserve hose

17 Air filter drain hose

18 Delay relay

19 Battery negative (–) lead

20 Oil level switch lead

21 Rear brake light switch lead

22 Light reduce relay

23 Rectifier/regulator

24 Stay 1

25 Down tube

26 Rear brake hose

27 Frame

28 Stay 2

29 Turn signal relay

30 Handlebar switch lead (left)

31 Silencer

32 Throttle position sensor lead

33 Carburetor heater lead

34 Thermo switch lead

35 Horn