Manual de Taller KAWASAKI KFX700 V-FORCE MANUAL TALLER 2004

KFX 700V FORCE

Quick Reference Guide

General Information 1

Periodic Maintenance 2

Fuel System 3

Cooling System 4

Engine Top End 5

Converter System 6

Engine Lubrication System 7

Eng ine Removal/Installation 8

Crankshaft / Transmission 9

Wheels / Tires 10

Final Drive 11

Brakes 12

Suspension 13

Steering 14

Frame 15

Electrical System 16

Appendix 17

This quick reference guide will assist

you in locating a desired topic or pro-

cedure.

•

Bend the pages back to match the

black tab of the desired chapter num-

ber with the black tab on the edge at

each table of contents page.

•

Refer t o the sectional table of con-

tents for the exact pages to locate

the specific topic required.

KFX 700 V FORCE

transmitted in any form or by any means, electronic mechanical photocopying, recording or otherwise,

without the prior written permission of Quality Assurance Department/Consumer Products & Machinery

Company/Kawasaki Heavy Industries, Ltd., Japan.

No liability can be accepted for any inaccuracies or omissions in this publication, although every possible

care has been taken to make it as complete and accurate as possible.

The right is reserved to make changes at any time without prior notice and without incurring an obligation

to make such changes to products manufactured previously. See your dealer for the latest information on

product improvements incorporated after this publication.

All information contained in this publication is based on the latest product information available at t he time

of publication. Illustrations and photographs in this publication are intended for reference use only and may

not depict actual model component parts.

LIST O F ABBREVIAT IONS

A ampere(s) lb pounds(s)

ABDC after bottom dead center m meter(s)

AC alternating current min minute(s)

ATDC after top dead center N newton(s)

BBDC before bottom dead center Pa pascal(s)

BDC bottom dead center PS horsepower

BTDC before top dead center psi pound(s) per square inch

degree(s) Celcius r revolution

DC direct current rpm revolution(s) per minute

F farad(s) TDC top dead center

degree(s) Fahrenheit TIR total indicator reading

ft foot, feet V volt(s)

g gram(s) W watt(s)

h hour(s) ohm(s)

L liter(s)

Read OWNER’S MANUAL before op erating.

EMISSION CONT ROL INFORMATION

To protect the environment in which we all live, Kawasaki has incorporated crankcase emission

(1) and exhaust emission (2) control systems in compliance with applicable regulations of the

California Air Resources Board.

1. Crankcase Emission Control System

A sealed-type crankcase emission control system is used to eliminate blow-by gases. The

blow-by gases are l ed to the breather chamber through the crankcase. Then, it is led to the

air cleaner.

Oil is separated from the gases while passing through the inside of the breather chamber

from the crankcase, and then returned back to the bottom of crankcase.

2. Exhaust Emission Control System

The exhaust emission control system applied to this engine family is engine modifications

that consist of a modified carburetor and an ignition system having optimum ignition timing

characteristics.

The carburetor has been calibrated to provide lean air/fuel mixture characteristics and opti-

mum fuel economy with a suitable air cleaner and exhaust system.

A maintenance free ignition system provides the m ost favorable ignition timing and helps

maintain a thorough combustion process within the engine which contributes to a reduction

of exhaust pollutants entering the atomosphere.

The Clean Air Act, which is the Federal law covering motor vehicle pollution, contains what is

commonly referred to as the Act’s "tampering provisions."

"Sec. 203(a) The following acts and the causing thereof are prohibited...

(3)(A) for any person to remove or render inoperative any device or element of design installed

on or in a motor vehicle or motor vehicle engine in compliance with regulations under this

title prior to its sale and delivery to the ultimate purchaser, or f or any manufacturer or dealer

knowingly to remove or render inoperative any such device or element of design after such

sale and delivery to the ultimate purchaser.

(3)(B) for any person engaged in the business of repairing, servicing, selling, leasing, or trading

motor v ehicles or motor vehicle engines, or who operates a fleet of motor vehicles know-

ingly to remove or render inoperative any device or element of design installed on or in a

motor vehicle or motor vehicle engine in compliance with regulations under this title follow-

ing its sale and delivery to the ultimate purchaser..."

NOTE

The phrase "remove or render inoperative any device or element of design" has been generally

interpreted as follows:

1. Tampering does not include the temporary removal or rendering inoperative of de-

vices or elem ents of design in order to perform maintenance.

2. Tampering could include:

a.Maladjustment of vehicle components such that the emission standards are ex-

ceeded.

b.Use of replacement parts or accessories which adversely affect the performance

or durability of the vehicle.

c.Addition of components or accessories that result in the vehicle exceeding the stan-

dards.

d.Permanently removing, disconnecting, or rendering inoperative any component or

element of design of the emission control systems.

WE RECOMMEND THAT ALL DEALERS OBSERVE THESE PROVISIONS OF FEDERAL LAW,

THEVIOLATIONOFWHICHISPUNISHABLEBYCIVILPENALTIESNOTEXCEEDING

$10,000 PER VIOLATION.

PLEASE D O NOT TAMPER WITH NOISE CONTROL SYSTEM

(US MODEL only)

To minimize the noise emissions from this product, Kawasaki has equipped it with effective

intake and exhaust silencing systems. They are designed to give optimum performance while

maintaining a l ow noise level. Please do not remove these systems, or alter them in any which

results in an increase in noise level.

Foreword

This manual is designed primarily for use by

trained mechanics in a properly equipped shop.

However, it contains enough detail and basic in-

formation to make it useful to the owner who de-

sires to perform his own basic maintenance and

repair work. A basic knowledge of mechanics,

the proper use of tools, and workshop proce-

dures must be understood in order to carry out

maintenance and repair satisfactorily. When-

ever the owner has insufficient experience or

doubts his ability to do the work, all adjust-

ments, maintenance, and repair should be car-

ried out only by qualified mechanics.

In order to perform the work efficiently and

to avoid costly mistakes, read the text, thor-

oughly f amiliarize yourself with the procedures

before starting work, and then do the w ork care-

fully in a clean area. Whenever special tools or

equipment are specified, do not use makeshift

tools or equipment. Precision measurem ents

can only be made if the proper instruments are

used, and the use of substitute tools may ad-

versely affect s afe operation.

For the duration of the warranty period,

we recommend that all repairs and scheduled

maintenance be performed in accordance with

this service manual. Any owner maintenance or

repair procedure not performed in accordance

with this manual may void the warranty.

To get the longest life out of your vehicle:

•

Follow the Periodic Maintenance Chart in the

Service Manual.

•

Be alert for problems and non-scheduled

maintenance.

•

Use proper tools and genuine Kawasaki Vehi-

cle parts. Special tools, gauges, and testers

that are necessary when servicing Kawasaki

vehicles are introduced by the Special Tool

Catalog or Manual. Genuine parts provided

as spare parts are listed in the Parts Catalog.

•

Follow the procedures in this manual care-

fully. Don’t take shortcuts.

•

Remember to keep complete records of main-

tenance and repair with dates and any new

parts installed.

How to Use This Manual

In this manual, the product is divided into

its major systems and these systems make up

the manual’s chapters. The Quick Reference

Guide shows you all of the product’s system

and assists in locating their chapters. Each

chapter in t urn has its own comprehensive Ta-

ble of Contents.

For example, if you want ignition coil informa-

tion, use the Quick Reference Guide to locate

the Electrical System chapter. Then, use the

Table of Contents on the first page of the chap-

ter to find the Ignition Coil section.

Whenever you see these WARNING and

CAUTION symbols, heed their instructions!

Always follow safe operating and maintenance

practices.

WARNING

This warning symbol identifies special

instructions or procedures which, if not

correctly followed, could result in per-

sonal injury, or loss of life.

CAUTION

This caution symbol identifies special

instructions or procedures which, if not

strictly observed, could result in dam-

age to or destruction of equipment.

This manual contains four more symbols (in

addition to WARNING and CAUTION) which will

help you distinguish different types of informa-

tion.

NOTE

This note symbol indicates points of par-

ticular interest for more efficient a nd con-

venient operation.

•

Indicates a procedural step or work to be

done.

Indicates a procedural sub-step or how to do

the work of the procedural step it follows. It

also precedes the text of a N OTE.

Indicates a conditional step or what action to

take based on the results of the test or inspec-

tion in the procedural step or sub-step it fol-

lows.

In most chapters an exploded view illustration

of the system components follows the Table of

Contents. In these illustrations you will find the

instructions indicating which parts require spec-

ified tightening torque, oil, grease or a locking

agent during assembly.

GENERAL INFORMATION 1-1

General Information

TABLE OF CONTENTS

Before Servicing ...................................................................................................................... 1- 2

Model Identification..................................................................................................... ............. 1- 5

General Specifications............................................................................................................. 1- 6

Unit Conversion Table .............................................................................................................1-9

1-2 GENERAL INFORMATION

Before Servicing

Before starting to perform an inspection service or carry out a disassembly and reassembly oper-

ation on a vehicle, read the precautions given below. To facilitate actual operations, notes, illustra-

tions, photographs, cautions, and detailed descriptions have been included in each chapter wherever

necessary. This section explains the items that require particular attention during the removal and

reinstallation or disassembly and reassembly of general parts.

Especially note the following:

(1) Dirt

Before removal and disassembly, clean the vehicle. Any dirt entering the engine will shorten the

life of the vehicle. For the same reason, before installing a new part, clean off any dust or metal

filings.

(2) B attery Ground

Disconnect the ground (–) wire from the battery before performing any disassembly operations

on the vehicle. This prevents the engine from accidentally turning over while work is being carried

out, sparks from being generated while disconnecting the wires from electrical parts, as well as

damage to the electrical parts themselves. For reinstallation, first connect the posit ive w ire t o the

positive (+) terminal of the battery

(3) Installation, Assembly

Generally, installation or assembly is the reverse of removal or disassembly. However, if i nstal-

lation or assembly sequence is given in this Service Manual, follow it. N ote parts locations and

cable, wire, and hose routing during removal or disassembly so they can be installed or assem-

bled in the same way. It is preferable to mark and record the locations and routing whenever

possible.

(4) Tightening Sequence

When installing bolts, nuts, or screws for which a tightening sequence is given in this Service

Manual, m ake sure to f ollow the sequence. When installing a part w ith several bolts, nuts, or

screws, start them all in their holes and tighten them to a snug fit, thus ensuring that the part has

been installed in its proper location. Then, tighten them to the specified torque in the tightening

sequence and method indicated. If tightening sequence i nstructions are not given, tighten them

evenly in a cross pattern. Conversely, to remove a part, first loosen all the bolts, nuts, or screws

that are retaining the part a 1/4–turn before removing them.

(5) Torque

When torque values are given in this Service Manual, use them. Either too little or too much

torque may lead to serious damage. Use a good quality, reliable torque wrench.

(6) Force

Common sense should dictate how m uch force is necessary in assembly and disassembly. If

a part seems especially difficult to remove or install, stop and examine what may be causing the

problem. Whenever tapping is necessary, tap lightly using a wooden or plastic-faced mallet. Use

an impact driver for screws (particularly for the removing screws held by non-permanent locking

agent) in order to avoid damaging the screw heads.

(7) E dges

Watch for sharp edges, as they could cause injury through careless handling, especially during

major engine disassembly and assembly. Use a clean piece of thick cloth when lifting the engine

or turning it over.

(8) H igh-Flash Point Solvent

A high-flash point solvent is recommended to reduce fire danger. A commercial solvent com-

monly available in North America is standard solvent (generic name). Always follow manufacturer

and container directions regarding the use of any solvent.

(9) Gasket, O-Ring

Replace a gasket or an O-ring with a new part when disassembling. Remove any foreign matter

from the mating surface of the gasket or O-ring to ensure a perfectly smooth surface to prevent

oil or compression leaks.

GENERAL INFORMATION 1-3

Before Servicing

(10) Liquid Gasket, Locking Agent

Clean and prepare surfaces where liquid gasket or non-permanent locking agent will be used.

Apply them sparingly. Excessive amount m ay block engine oil passages and cause serious dam-

age.

(11) Press

When using a press or driver to install a part s uch as a wheel bearing, apply a small amount of

oil to the area where the two parts come in contact to ensure a smooth fit.

(12) Ball Bearing and Needle Bearing

Do not remove a ball bearing or a needle bearing unless it is absolutely necessary. Replace any

ball or needle bearings that were rem oved with new ones. Install bearings with the manufacturer

and size marks facing out, applying pressure evenly with a suitable driver. Apply force only to the

end of the race that contacts the press fit portion, and press it evenly over the base component.

(13) Oil Seal and Grease Seal

Replace any oil or grease seals that were removed with new ones, as removal generally dam-

ages seals. Oil or grease seals should be pressed into place using a suitable driver, applying a

force uniformly to the end of seal until the face of t he seal is even with the end of the hole, unless

instructed otherwise. When pressing in an oil or grease seal which has manufacturer’s marks,

press it in with t he marks facing out.

(14) Circlip, R etaining Ring, and Cotter Pin

When installing circlips and retaining rings, take care to compress or expand them only enough

to install them and no more. Install the circlip with its chamfered side facing load side as well.

Replace any circlips, retaining rings, and cotter pins that were removed with new ones, as re-

moval weakens and deforms them. If old ones are reused, they could become detached while

the vehicle is driven, leading to a major problem.

(15) Lubrication

Engine wear is generally at its maximum while the engine is warming up and before all the sliding

surfaces have an adequate lubricative film. During assembly, make sure to apply oil to any sliding

surface or bearing that has been cleaned. Old grease or dirty oil could have lost its lubricative

quality and may contain foreign particles that act as abrasives; therefore, make sure to wipe it off

and apply f resh grease or oil. Som e oils and greases in particular should be used only in certain

applications and may be harmful if used in an application for which they are not intended.

(16) Direction of Engine R otation

To rotate the crankshaft manually, make sure to do so in the direction of positive rotation. Pos-

itive rotation i s counterclockwise as viewed from the left side of the engine. To carry out proper

adjustment, it i s furthermore necessary to rotate the engine in the dir ection of positive rotation as

well.

(17) Replacement Parts

When there is a replacement instruction, replace these parts with new ones every time they are

removed.

Replacement parts will be damaged or lose their ori ginal function once they are removed. There-

fore, always replace these parts with new ones every time t hey are removed. Although the pre-

viously mentioned gasket, O-ring, ball bearing, needle bearing, grease seal, oil seal, circlip, and

cotter pin have not been so designated in their respective text, they are r eplacement parts.

(18) Electrical Wires

All the electrical wires are either one-color or tw o-color. A two-color wire is identified first by the

primary color and then the stripe color. For example, a yellow wire with thin red stripes is referred

to as a “yellow/red” w ire; it would be a “red/yellow” w ire if the colors were reversed. Unless in-

structed otherwise, electrical wires must be connected t o wires of the same color.

1-4 GENERAL INFORMATION

Before Servicing

Two-Color Electrical

(19) Inspection

When parts have been disassembled, visually inspect these parts for the following conditions

or other damage. If there is any doubt as to the conditi on of them, replace them with new ones.

Abrasion Crack Hardening Warp

Bent Dent Scratch Wear

Color change Deterioration Seizure

(20) S pecifications

Specification terms are defined as follows:

"Standards" show dimensions or performances which brand-new parts or systems have.

"Service Limits" indicate the usable l imits. If the measurement shows excessive wear or dete-

riorated performance, replace the damaged parts.

GENERAL INFORMATION 1-5

Model Identification

KSV700–A1 Left Side View

KSV700–A1 Right Side View

📥 ¿Necesitas el PDF Original?

¿Te vas a quedar a medias con el diagnóstico?

Llévate este manual + La Biblioteca VIP Completa